Member Since: 09 Oct 2012
Location: Cambridge
Posts: 181
Limp mode help please!
Hello all
We have a 12 D4 HSE 148,490 km that has gone into limp mode for the first time yesterday whilst out on a long drive
We’ve had a nightlong suspension issue for around 12 months that our local garage hasn’t been able to diagnose, but I think it’s to do with a ride height sensor?
When we press the suspension down button we would occasionally get an Amber suspension fault, a reset of the ignition would normally clear this, but occasionally you would get the Red warning for around 2 mk utes and then it would clear!
I’ve just looked at the current fault codes and this is what I am showing:
VIN: SALLAAAG5CA624312
L319 - Discovery 4 2012
Vehicle scanned on 17-10-2022 09:48
Using IIDTool BT V3.0 B2481
ABS-Brake Module
U0421-68 (28) Invalid data received from ride level control module - Algorithm based failure - event information
( on 06-10-2022 10:50:54 at 147508 km )
BCM-Body Control
B1B01-87 (28) Key transponder - Bus signal/message failure - missing a message
( on 06-10-2022 10:50:14 at 147508 km )
DDM-Driver Door
B1164-15 (2F) Right mirror heater output - General electrical failure - circuit short to battery or open
( on 06-10-2022 10:49:45 at 147508 km )
PDM-Passenger Door
B1163-15 (2F) Left mirror heater output - General electrical failure - circuit short to battery or open
( on 14-10-2022 17:06:51 at 148189 km )
RLM-Suspension
C1A13-64 (2C) Pressure does not decrease when venting gallery - Algorithm based failure - signal plausibility failure
( on 06-10-2022 10:50:53 at 147508 km )
SASM-Steering Angle
U0300-55 (2F) Internal control module software incompatibility - System programming failure - is not configured
( on 08-10-2022 13:05:19 at 147572 km )
I cleared the codes and then pressed the ride height adjuster and received these codes:
VIN: SALLAAAG5CA624312
L319 - Discovery 4 2012
Vehicle scanned on 17-10-2022 09:50
Using IIDTool BT V3.0 B2481
ABS-Brake Module
U0421-68 (2B) Invalid data received from ride level control module - Algorithm based failure - event information
( on 17-10-2022 09:49:56 at 148490 km )
DDM-Driver Door
B1164-15 (2F) Right mirror heater output - General electrical failure - circuit short to battery or open
( on 17-10-2022 09:49:34 at 148490 km )
PDM-Passenger Door
B1163-15 (2F) Left mirror heater output - General electrical failure - circuit short to battery or open
( on 17-10-2022 09:49:37 at 148490 km )
RLM-Suspension
C1A13-64 (AF) Pressure does not decrease when venting gallery - Algorithm based failure - signal plausibility failure
( on 17-10-2022 09:49:56 at 148490 km )
Can anyone please help??
17th Oct 2022 9:06 am
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6402
looks like you need to replace or rebuild your compressor
G
17th Oct 2022 9:33 am
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6402
Member Since: 09 Oct 2012
Location: Cambridge
Posts: 181
Hi G thank you for the reply. Is there anything I can check to confirm this?
What sort of a job is this to complete?
17th Oct 2022 9:36 am
r6demon
Member Since: 09 Oct 2012
Location: Cambridge
Posts: 181
Ok so I’ve checked the compressor and there is a leak from the blue pushfit. I’ve decided to rebuild the drier so dropped the compressor down to get to the drier release screw on top.
I’ve bought a drier rebuild kit from landy air on eBay so wish me luck!
I don’t seem to have a crack in the drier lid though, but I’ll replace it anyway!
17th Oct 2022 2:04 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6402
wow quick action on it?
nice
17th Oct 2022 2:07 pm
r6demon
Member Since: 09 Oct 2012
Location: Cambridge
Posts: 181
Thank you! I’ll let you know how I get on! If this doesn’t work it’s a compressor ….. eeeek!!
The compressor hums away, so hopefully we are all good!!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
