Member Since: 06 Jun 2020
Location: Liverpool
Posts: 23
It could be me in all honesty, i thought i had read it needed a live that came on and off basically with the doors being locked and unlocked ? Going back together for tonight if i need to alter wiring it will be another day
8th Jun 2020 5:48 pm
Lukie
Member Since: 06 Jun 2020
Location: Liverpool
Posts: 23
Wiggs i knew i had seen something somewhere
This is all like riding a bike you never do forget after the 100 times this year of helping people !
Have taken photos along the way and will post up when back in doors
8th Jun 2020 5:53 pm
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14372
Fuse 58 is a “ wake up wire “
Comes on when car unlocked .. goes off when the car goes to sleep .G4 Gone ...but not forgotten
8th Jun 2020 6:11 pm
Lukie
Member Since: 06 Jun 2020
Location: Liverpool
Posts: 23
Wiggs thank you so much, you are not only a fantastic guy for doing the mod 10 years ago, but fantastic for still having the patients to support people doing this mod for the first time now 10 years on... here is my results
IID had to set CCF to bluetooth with cradle, the most wire i got off ebay around £10 the power wire i used JST P2 connector these i got for around £4 for 10 sets (will be used for other mods)
Had it in my head that this install would be slightly different once something is in my head very difficult to change it, but certainly worked, objective to install bluetooth unit in void by gear lever
Firstly to pull apart H trim and trim around gear lever
Then to look at fiber optic cable, this is more sensitive then a wire, it can be curverd but not bent, im careful on install but should i need access in the same area for something else i wouldnt be as careful, the fiber optic loop slide down the plastic support for radio on right hand side, i taped it together leaving a loop at the bottom then slide it down, i had to reroute at the top to avoid contact between MOST cable and H panel
Then with the grinder i cut off the 4 locating holes on the bluetooth unit, while this is out (if following this) cut a line in the plastics bottom left hand side for the MOST and power cables, this allows for the cables to be fitted and never need to move them out the way
Something i personally did find (common knowledge or not i am unaware as yet) if you dont have your heater panel fitted in the car it simply wont start (will order a spare heater panel incase the car one day wont start, will put a post up somewhere else about this)
I took an earth feed from the 12v socket and my 12+ feed from fuse 58 as advice by wiggs
You can test everything works without key in ignition, simply hit power button on radio
Put everything back in and it was like i was never there
9th Jun 2020 7:58 am
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14372
So is it all working ??G4 Gone ...but not forgotten
9th Jun 2020 4:56 pm
Lukie
Member Since: 06 Jun 2020
Location: Liverpool
Posts: 23
Wiggs everything is in and working fine pal thank you, your PDF was a great help i had read it at some point but as you can imagine 60+ pages when your in the middle of an install
9th Jun 2020 6:26 pm
Lenny1974
Member Since: 10 May 2020
Location: Bristol
Posts: 70
The bluetooth works !!!!
Friend just took it to the garage and they managed to update the CCF files and my frined phoned me from the Disco.
Thanks to all that contributed and keep up the good work.
1st Jul 2020 3:45 pm
Sketch08
Member Since: 22 Jun 2020
Location: Farmborough
Posts: 5
Hi I am also desperately trying install a phone module into my D3 2008 (SE). It has no phone to start with and I have already converted the D4 satnav successfully (thank you wiggs for your other thread on that).
I have installed the D3 phone harness, module, old bluetooth and nothing is working. I want to put the D4 bluetooth module in but am struggling to justify purchasing the MSV-2 faultmate to complete this task.
Can anyone help? Sorry if I have done something dumb, any advice would be greatly appreciated.
6th Jul 2020 6:30 am
Lukie
Member Since: 06 Jun 2020
Location: Liverpool
Posts: 23
There are a few people both on here and facebook that travel the country doing diagnostics/ccf editing/ upgrades
i am sure it wouldnt be long before someone is found close to you for the software update
6th Jul 2020 7:01 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10676
Sketch - As your D3 wiring is the retrofit system VUB501151, this should work without a code reader/configurator. (providing it is compatible with your phone). It does not make use of the displays in the car. Use your phone to search for bluetooth devices while sat in your car with the ignition on I
As/if you have it fitted you may as well try get it working
Please start another thread if you want help with getting this system working.
Otherwise as you have D4 Nav the only other LR option is a D4 BT, see pictures above from Lukie.
Usually people put a post in the IID section, with title, "CCF edit required in Farmborough"
and then in the post say to enable D4 BT
6th Jul 2020 8:20 am
zuppo
Member Since: 03 Jan 2018
Location: Toronto
Posts: 3
Hello to you all! I have been learning so much with this forum and thus very grateful. This is my first post and hoping for assistance.
I'm tempted to replace my D3 with a D4 BT module but I find a couple of different part numbers:
AH22 10F845 AA and 8H22 10F845 AA. Both have the MOST connections and are from 2010-2012 D4's. Is there a difference between the 2 part numbers? Should I be concerned about the year of the D4 from which the modules came from, regarding functionality?
7th Feb 2021 4:55 am
zuppo
Member Since: 03 Jan 2018
Location: Toronto
Posts: 3
Actually there is a 3rd part number I came across...AH42-10F845-AA
7th Feb 2021 5:15 am
Huge Halford
Member Since: 30 May 2013
Location: West Midlands
Posts: 275
Hi Guys I’m after the plug and play most cable.. any links where to get one from. Mods:-
Beanie Grill,Side Steps,Colour-coded wheel arches, Door handles and Bumpers,Rear Bumper Exhaust Trim,Remote Start FBH,2014 D4 rear lights,Reversing camera GVIF enabled,D4 Bluetooth Module, Puddle lighted wing mirrors
To do list:-
Waxoyl the Underside.
23rd Feb 2021 4:53 pm
Mashi
Member Since: 02 Mar 2021
Location: kazakhstan
Posts: 3
Hello there,
My name is Max. I'm from Kazakhstan. I have been reading this forum for a long time. I need some expert help with how to install the Bluetooth module in my D4 2010.
I have an LRD4 2010 - S edition. 2,7L
In five years of car ownership, I installed front and rear seats from RRS, Facelift 2016, rain and light sensor, steering wheel (heating) from RRS, Heated windshield, and now I want to install a BT module.
I bought D4 with base multimedia (Black small screen) without BT but with a new engine this point was very important for me ))
For BT installation I bought some parts:
1. steering wheel with phone control bottoms
2. microphone in the overhead dome
3. BT module. (looks like D3 module)
I thought I bought all parts, but it's not so.....
At first, I installed the steering wheel, Cruise control, and heating working very well. Next, I plugged a mic and removed the right back panel in the trunk. I was surprised when I have not found wires for BT.
What do I do?
Should I try to find wiring under the carpet or I must buy this part of the wiring? What else could I be missing?
I hope for your help and sorry for my English.
Thank you!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
