I don't think the Danhag has a 'plip' option as well as the GSM. If you want both options then BAS is the one for you (but no HVAC option, it'll be FBH only).
If you want Danhag then you should get their GSM Controller (W-bus version) and the Landrover IPCU unit (that will control your HVAC and comes with the necessary wiring harness).
You may also need an FBH wire from the shop here depending on your own Disco.
There are many guys here with knowledge going back to the group buy - hopefully they can confirm what I have just said.
Can anyone confirm if I should be setting my unit up as W-Bus 3 or W-Bus 4 below when setting up the SMS configuration on the Danhag site:
30 Output signal /
Heater Type
(Sh.-Typ)
0: Park heater
1: +12V
2: Ground
3: W-Bus
4: W-Bus PRO
The unit Danhag have sent to me is not called 'PRO' any longer, simply 'W-Bus' but i'm thinking it is the same thing. It definately i8sn't the 'Basic' GSM unit.
Any help on whether to set it up as either option 3 or 4 would be gratefully received from the Danhag users out there.
last question (for a while anyway), is there any particular climate setting I need to leave the car in before I switch it off to ensure the cabin blows warm air the following morning? (last attempt I made would only blow cold air through the cab fans even though the FBH was seriously hot and had been running for a good 20 minutes before the fans even kicked in.
Cheers,
Darren
25th Nov 2013 7:20 pm
redlabel
Member Since: 11 Oct 2010
Location: Tromsdalen
Posts: 25
Any chance that this group buy will happen again?
31st Mar 2014 1:30 pm
StevieJ4558
Member Since: 04 Aug 2011
Location: Edinburgh
Posts: 94
"Danhag GSM controller + HVAC module"
Guys not sure if anyone will be interested but I have traded in my D3 today and have a complete and working GSM unit for sale, I got it about a year ago and it worked great.
Would be looking for£150 Ono delivered in the uk.
CheersStevie J
2nd Apr 2014 12:06 am
WEERAB
Member Since: 12 Jan 2014
Location: staffs
Posts: 2
do you still have installation instructions with it stev j
22nd Apr 2014 10:11 am
LX0850
Member Since: 28 Apr 2010
Location: Luxembourg
Posts: 62
DanHag / Car Chief - Removing the GSM Unit
A while back I realised that if you have to remove the GSM unit for any length of time and you want to remove the IPCU-Module as well then the climate control is probably going to throw all sorts of errors because of the various cables that were cut through during the install.
- I've put the wiring diagram in my gallery :
Click image to enlarge
So, I e-mailed Danielle over at Danhag in Berlin and they VERY KINDLY sent me a pcb-side connector :
I'm going to solder it onto a bit of vero-board and try and find a nice box to put it in.
That way there is no danger of a short circuit - it's going to hang around behind the dash for a while probably......
If anybody is interested I can get more of these connectors - if there's enough interest the price is going to be really low.
Let me know.
-Graham-
31st Oct 2014 2:14 pm
LX0850
Member Since: 28 Apr 2010
Location: Luxembourg
Posts: 62
When the IPCU-Module fails......
Hello everyone,
A couple of weeks ago I noticed that I wasn't getting any heating inside the car even if I turned up the dials to full.
It took a couple of hours of searching - because I'd completely forgotten that the DanHag IPCU-module was installed (I had removed the GSM unit over a year ago).
One thing that I hadn't noticed is that the PROG lamp didn't blink and the blowers activate for a while when I started the car.....
Don't forget, if you want to remove the IPCU-Module completely you will have to bridge/short the wires in the connector to restore the original wiring again.
PS: You will need to reset the FBH because it will be locked-out and won't start even after you have fixed the cable problems.
Stay warm!
16th Oct 2017 9:39 am
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18563
Have you installed a bridge to restore it or put the vehicle wiring back to original?06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
16th Oct 2017 10:45 am
LX0850
Member Since: 28 Apr 2010
Location: Luxembourg
Posts: 62
It is easy to bridge the (yellow and green) and (blue and purple) wires in the IPCU connector of the DanHag wiring loom using solid copper wires.
(see the wiring diagrams in my gallery).
I was intending to put a specially made bridge using a "proper" connector (see my gallery) - but I couldn't find the connector.......
(Since then I found it hiding in the garage - but it's too late now).
16th Oct 2017 1:04 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18563
Yes I saw the connector in your post above 06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
