|
sean 471
Member Since: 26 Apr 2011
Location: Sheffield
Posts: 2990
|
Can we get some engine numebrs for these. its making me nervous
|
23rd Feb 2012 9:20 am |
|
|
chalky
Member Since: 22 Aug 2008
Location: Yorkshire
Posts: 3145
|
Yep I agree, engine numbers would be good !
My @rse is twitching too ! Only dead fish go with the Flow !
|
23rd Feb 2012 11:23 am |
|
|
DSL
Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73012
|
Agree, engine number would be good but thought peeps might be nervios of putting official numbers on open forum.
Last edited by DSL on 23rd Feb 2012 11:54 am. Edited 1 time in total
|
23rd Feb 2012 11:25 am |
|
|
sean 471
Member Since: 26 Apr 2011
Location: Sheffield
Posts: 2990
|
Whose peeps?
|
23rd Feb 2012 11:46 am |
|
|
DSL
Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73012
|
Peeps = people.
|
23rd Feb 2012 11:54 am |
|
|
sean 471
Member Since: 26 Apr 2011
Location: Sheffield
Posts: 2990
|
OK we could always ask them through pm and keep the numbers in confidence.
Even if we only use it for ourselves to build a picture. If we have where the repair work has been completed it might give us some reason for argument.
I think LR are aware of this. One guy I spoke to last year told me the same thing happened when the car was three weeks old, the engineers from LR were crawling all over it.
|
23rd Feb 2012 12:00 pm |
|
|
DSL
Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73012
|
They might have been all over it but did they contribute to the cost of the new engine? Would be a precedent they wouldn't want to set.
|
23rd Feb 2012 12:03 pm |
|
|
sean 471
Member Since: 26 Apr 2011
Location: Sheffield
Posts: 2990
|
Yes they changed the engine under warrenty though, somebody on here says landrover paid for the work, will look to see if it was done outside LR warrenty
|
23rd Feb 2012 12:07 pm |
|
|
sean 471
Member Since: 26 Apr 2011
Location: Sheffield
Posts: 2990
|
SteveNorman wrote:have seen this too, low mileage, 57000 miles 57 plate vehicle. Was about a year ago, & was out of warranty, but Landrover paid for the new engine. It was the tensioner casting brroken on this one.
My guess is something else goes tight, causing the belt to put excess pressure on the casting of the tensioner & breaking it.
Regards
Steve
Here we go
|
23rd Feb 2012 12:09 pm |
|
|
DSL
Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73012
|
That's a result!
|
23rd Feb 2012 12:12 pm |
|
|
Alex08
Member Since: 09 Nov 2006
Location: Glasgow
Posts: 1600
|
Would there be any way to tell this was about to happen by visual inspection? Crack noticeable in a visible place?
|
23rd Feb 2012 1:55 pm |
|
|
Flack
Member Since: 06 Sep 2006
Location: Preston Lancashire
Posts: 6300
|
I am doing some belts this week so I will take a close look at this one,I have been keeping an eye on this problem while doing the belt changes..and not seen anything up to now.
Flack
|
23rd Feb 2012 1:59 pm |
|
|
sarumlight
Member Since: 07 Nov 2008
Location: Off the Plain
Posts: 1592
|
Isn't Steve's question important though: Did these engines end up mullered because the tensioner casting failed, or did the tensioner casting fail because something caused a massive stress on the belt and it just happens to be the weakest link. For example, one of the camshaft bearings siezed, or the fuel pump siezed?
We would only know this if one of these engines was stripped down, and checked over very carefully, and if the valve / head is damaged I'm not sure it'd be easy to tell what the root cause actually was.
|
23rd Feb 2012 5:23 pm |
|
|
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20822
|
My money is on a weak casting
If something were to seize, the belt would more likely shred itself against either of the cam pulleys or crank pulley, I would imagine.
Unless it was something along the lines of the cambelt tensioner has been set too tight, but that wouldnt explain why it is only a batch of 57 plate cars My D3 Build Thread
TDV8 Retrofit Build Thread
|
23rd Feb 2012 7:21 pm |
|
|