Got mine today thanks Mikey, will be fitted tomorrow replacing the broken one on my phone remote set up
Beanie, what remote phone setup are you using? Imam interested to know
Kev I have a version if this, basically a GSM electric gate receiver wired into the back of the 1533, linked in now is the item in the second post to act as a direct remote too
IID Pro MV License - D3, D4 & RRS - Enabling, Updates, D4 & RRS Timed / Remote Climate, D4 Bluetooth fitting
PM me for details
Owner of the original "Beanie" grille
D4 & RRS style D3 grilles made to order
9th Dec 2013 8:51 pm
Staffiedrone
Member Since: 21 Jul 2013
Location: Stafford
Posts: 58
Got mine today thanks very much Mikey.D3 2005
Previously
Defender 1992 110 CSW
RRC TDi 1993
RRC 1981
s 11a LWB Safari
9th Dec 2013 10:28 pm
F355GTS
Member Since: 10 Nov 2008
Location: North Hampshire
Posts: 849
Mine arrived today, thanks Mike Mark
10th Dec 2013 3:16 pm
mrszymon
Member Since: 17 Apr 2012
Location: London
Posts: 425
Arrived! Many thanks, will fit this weekend
10th Dec 2013 4:03 pm
1andrewm
Member Since: 26 Feb 2010
Location: South Yorkshire
Posts: 42
Arrived to today, many thanks all the best..andymAndym Expert Beverage
10th Dec 2013 9:02 pm
G_Cam
Member Since: 12 Aug 2010
Location: Fife
Posts: 2061
Looking for some inspiration....
Just wondering how and where everyone plans to mount their timers....1 TR6 Rusting away quietly
1 FARR UTV SOLD
1 International Harvester SOLD
7 x D3 all SOLD
2 x D4 both SOLD
1 x Mrs D4 'Panther' SOLD
1 x Outlander van SOLD
1 continual stream of car parts and me living in the garage...
10th Dec 2013 11:19 pm
Somerset Jem
Member Since: 07 Jul 2011
Location: Somerset
Posts: 435
I've got the same dilemma G_Cam. Picked my timer up from Martin on Saturday as I was passing and my remote plip and box arrived from Hong Kong (or could be China?) yesterday. I was thinking of fitting everything under the bonnet next to the battery as I think I will always use the remote to start her up. This would save routing cables through to the car interior and save the issue of where to place the timer. Or am I about to do something really stupid???
Jem2005 D3 HSE side steps, tints, tlo fridge, egr's blanked.
IID Pro MV License - D3, D4 & RRS - Enabling, Updates, D4 & RRS Timed / Remote Climate, D4 Bluetooth fitting
PM me for details
Owner of the original "Beanie" grille
D4 & RRS style D3 grilles made to order
10th Dec 2013 11:27 pm
Somerset Jem
Member Since: 07 Jul 2011
Location: Somerset
Posts: 435
Reassuring Beanie, I suppose it just means you can't see the run time on the display, but I'll be having a croissant and a nice cup of coffee then anyway (or still in bed!)
Jem2005 D3 HSE side steps, tints, tlo fridge, egr's blanked.
I put a flashing LED linked to the output pin 4 inside the car by the drivers air vent to show when it's running from the remote Altox GSM FBH controller thread
IID Pro MV License - D3, D4 & RRS - Enabling, Updates, D4 & RRS Timed / Remote Climate, D4 Bluetooth fitting
PM me for details
Owner of the original "Beanie" grille
D4 & RRS style D3 grilles made to order
10th Dec 2013 11:34 pm
sasdiscos
Member Since: 22 Feb 2013
Location: Northants
Posts: 889
Have you sent mine yet mate. No sign yet.
Cheers.You remind me of a younger me, not much younger mind...perhaps even a little older!
11th Dec 2013 3:44 pm
Shooterneil
Member Since: 12 Dec 2012
Location: Tamworth
Posts: 50
So I have soldered the 2 wires to the back of my timer and have a remote but
Were do I put the wires
It's got dc12v - 2ch latched on the lid but no instructions I can see were to put the power and earth
18th Dec 2013 7:36 pm
Tufty
Member Since: 13 Jul 2010
Location: UK
Posts: 481
You don't really want latched as it is surposed to mimik the press of the button, should be momentary some are switchable some you have to swap the chip type. It's normally a+ b (a being normally open, b being common)
On a different note got mine today as I actually got into the office....
Cheers Mike
18th Dec 2013 7:43 pm
Shooterneil
Member Since: 12 Dec 2012
Location: Tamworth
Posts: 50
it's changeable I got the one in the link at the top of the page
So is it' just trial and error now stick the wires in a press the button
18th Dec 2013 7:49 pm
Tufty
Member Since: 13 Jul 2010
Location: UK
Posts: 481
If that's the case the instructions are on the eBay page in the link,
put the link on M and your two wires on a+b then power up, all should be good.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
it's changeable I got the one in the link at the top of the page
