Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
I have enabled both cornering light settings in the CCF but I'm not getting a voltage to the headlight plug on pin 4
Can the voltage be seen without the headlight connected or does it need a load
Does car need to be in D or is P ok for testing
28th Nov 2015 5:22 pm
gvw
Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
Ok, has to be in D
The LEDs are fitted are also polarity conscious when fitted to the car.
Not 100% happy with the colour though as they are not an exact match for the xenons and make them look yellow in comparrison but at least they're working
28th Nov 2015 8:03 pm
gvw
Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
Matt, do you have a picture of these on with the xenons in order to compare the colour?
29th Nov 2015 6:19 pm
mattlidster
Member Since: 30 Jul 2011
Location: Poole Dorset
Posts: 128
Def a bit Yellow
5th Dec 2015 11:18 am
M3DPO
Member Since: 22 Sep 2010
Location: Notts.
Posts: 8228
Anybody managed to do this on a 2014my facelift?It can when others can't,
It will when others won't,
It goes where others don't.
10th Feb 2018 11:40 am
Famousfive
Member Since: 12 Aug 2014
Location: Southampton
Posts: 1832
MY14 Retroft Cornerning
I'd say impossible.
Cornering on the MY14 lights is driven from a couple of LED's on top of the semi circular cut outs on the bottom of the lamp - see picture - unit is upside down in this image.
Can't see how this could be easily retrofitted ... so I bought a pair of ABL-Xenons that have them as standard Stolen - D4 Loire Blue
D4 Bali Blue
Managed to get the blanks out of my headlight units and fitted the LED's shown in a previous post.
The Cree LED's are yellow coloured but I think they look OK in situ.
I'm still awaiting the correct pins to be delivered so couldn't complete the install but I powered up the LED's on the bench and the colour should complement the xenons pretty well
Also note that the LED units I fitted were not polarity conscious?
Thanks for showing how to carry this out as there is no way I would have started melting my headlights without guidance from this forum
How did you get the blanks out exactly? I'd like to do this to mine too.1972 Range Rover Classic 2 door V8
2013 Land Rover Discovery 4 HSE - SCRAPPED
2016 Land Rover Discovery 4 Landmark
2022 Volvo XC40 T5 PHEV 282HP FWD 3 cylinder!
14th Feb 2018 12:58 pm
gvw
Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
As others have mentioned on an earlier page I used a hot drill bit or screwdriver and carefully melted the plastic and removed the blank in sections.
I remember it being a bit fiddly but not too bad
14th Feb 2018 7:28 pm
DiscoJeffster
Member Since: 27 Feb 2016
Location: Perth
Posts: 204
Sorry to drag this one back up but I've tried this and cannot make it work. I've got a 2010 D4 HSE. I've fitted some H9 globes, got the correct pins, fitted to pin 4 and 16 as described. I've confirmed the red wire is in the harness and pin 16 has a black for the earth.
Within the IIDTool I've tried the CCF mod but was confronted with
Cornering Lamps (1)
Cornering Lamps (2)
I tried enabling 1 and tested. I tried in the driveway, turned on the headlight tried indicators, no luck. Saw to try when in Drive. Placed into drive, handbrake on, indicator, gingerly got out the car (hoping the handbrake holds lol), still nothing. Checked left and right.
Tried enabling the second cornering lamps option (forgot to disable the first admittedly), still nothing. Disabled Cornering Lamps 2 option. Tried Cornering Lamps (2) on its own. No good.
I'm perplexed now. Admittedly its day time so I'll wait until this evening and go for a drive to see if it works on setting Corner Lamps 1. I can't see what I can have done wrong. A globe is a globe (I've not used LED). Wiring is straight forward and in existence so I'm very confused.
If anyone knows what the two Cornering Lamps options are for I'd be interested.
I note again the error B123A-15 Front left turn signal - General Electrical Failure - circuit short or to battery or open. Same for right. Turn signals are working fine, so presumably related to the above.
I don't get it, all the harness wiring is there, so not sure why it's difficult. Someone mentioned early D4s needed the earth wiring added, but mine has the earth run to pin 16 - I presume given it's there it's actually connected in the harness?
Cheers
1st Jul 2018 5:52 am
gvw
Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
Have you checked with a meter if you’ve got a voltage on pin 4?
1st Jul 2018 12:43 pm
DiscoJeffster
Member Since: 27 Feb 2016
Location: Perth
Posts: 204
I admit no I haven’t as I presumed it was much like other “smart” cars that if it doesn’t find a load there equivalent to a globe it won’t light up the circuit.
I will go through basic tests such as powering the light through the plug to confirm the globes work and work from there. I presume it triggers the 12v circuit and not the earth to enable the circuit however I’ll have to take a look at the wiring harness to confirm.
1st Jul 2018 1:32 pm
DiscoJeffster
Member Since: 27 Feb 2016
Location: Perth
Posts: 204
So yep, 12V is activated, pins 4 and 16 are correct. I can't explain it so back to simple diagnosis - confirm globes work in light housing manually, then troubleshoot from there.
Click image to enlarge
1st Jul 2018 1:44 pm
gvw
Member Since: 16 Jan 2012
Location: South Yorkshire
Posts: 872
At least that narrows it down a bit for you
1st Jul 2018 9:33 pm
DiscoJeffster
Member Since: 27 Feb 2016
Location: Perth
Posts: 204
Kill me now? How can this be so hard?
Wiring in harness. Check
Earth working. Check
Globe powered manually in light. Check
IIDTool set to cornering lamps. Yes. Check
Lamps not working. Check. Grrrr.
I have enabled both cornering light settings in the CCF
you've only enabled option 1 … tried reading the thread to see what 1 vs 2 does but …
a. it's a long thread
b. need more caffeine to function this morning.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
