thanosgr
Member Since: 19 Aug 2016
Location: Athens
Posts: 7
|
Hi Narpy
I guess you are familiar with the correct battery voltage for Disco 3 .I have 12.4 - 12.9 and 14.6 volts when the engine is running .lt seems strange to me.
Let me know your thoughts
Best Regards
|
 22nd Aug 2018 9:43 pm |
|
|
Wyatt
Member Since: 23 Dec 2017
Location: Australia
Posts: 5
  
|
Hi there, my 2006 Disco 3 is dropping around 30mm in the front over 3-4 days. If drivers door is left open it does not move. I have replaced the front valve block and cleaned the rear valve block. Could it be the dryer dissident breaking down? Any advice welcome. Hi there, my 2006 Disco 3 is dropping around 30mm in the front over 3-4 days. If drivers door is left open it does not move. I have replaced the front valve block and cleaned the rear valve block. Could it be the dryer dissident breaking down? Any advice welcome.
|
| 11th Sep 2018 8:42 pm |
|
|
tony gt
Member Since: 29 Jul 2018
Location: cardiff
Posts: 10
 
|
Air suspension failure lights on,
I checked on the forum, thank god!
Soapy water test revealed the classic crack in the face of the air dryer next to the compressor. New compressor off flea bay, cost £45.00. Two hours work  later,,,,, no fault, the suspension is now fine!
Thanks so much to the contributors on the forum who have saved me hundreds of pounds at the stealers or else where. RR classic, dead in Ireland,
TD300, sold to a friend but totally restored,
TD5, gone but still going,
Ginetta G27 v8,
Porsche boxter,
low cost track car,
Disco 3 2008
|
| 14th Sep 2018 4:55 pm |
|
|
Danielle7
Member Since: 03 Nov 2018
Location: Canterbury Kent
Posts: 3
 
|
Hi since my husband had the car reversed on ramps to do the handbrake actuator, it was in the air about 4 hours, anyway took off the ramps and now every time you start it it raises at the front to I presume off road and the rear stays at normal height? Drive a few miles and it levels out to normal height? Please help. He’s cleaned the sensors and checked they are in ok but wonders if he has knocked them while doing handbrake?
|
| 3rd Nov 2018 9:57 am |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1822
|
Height is determined by the height sensors, so the fronts are the problem, just might be sticky/mud etc stopping them working properly. There have been connector/broken wire problems with the sensors
|
| 10th Nov 2018 9:15 am |
|
|
Danielle7
Member Since: 03 Nov 2018
Location: Canterbury Kent
Posts: 3
|
Hi thanks, he gave the rear ones a clean and now the rear raises and the front stays standard height
|
| 10th Nov 2018 9:31 am |
|
|
alexrose
Member Since: 23 May 2018
Location: Surrey
Posts: 28
 
|
Just recently my 05 D3 HSE has been going into extended mode when I select access mode (I select access mode whenever I get out, otherwise wife and kids find it a bit of a jump!)
Selecting access mode again drops the vehicle, I was wondering if I might have crud on sensors or something like that?
|
| 4th Mar 2019 10:53 pm |
|
|
Justjoe
Member Since: 16 Jul 2019
Location: Preston
Posts: 15
|
Hello, my d3 says suspension normal height only. Just wondering if theres anything i can check before i go get it plugged in?
Thanks
|
| 20th Jul 2019 6:48 pm |
|
|
longbow
Member Since: 03 Oct 2011
Location: sussex
Posts: 7
|
hi, my 58 d3 loses height on all four corners overnight, dash shows suspension fault and it still goes up when selected , took out fuse 26 as suggested on forum and all corners stayed up, can I assume that there are no leaks from reservoir to suspension airbag's? and if so what next, all help very much appreciated, thanks all. PS just went out and unlocked door didn't put key in ignition and car lost height, is that significant does it point to anything thanks again.
|
| 1st Aug 2019 10:25 am |
|
|
Disco chap
Member Since: 28 Jul 2021
Location: Kent
Posts: 1
|
Hi I have a 2009 disco 3 about a month ago suspension light come on and said normal height only so could still drive it and then a week later it said slow rising so replaced compressor and relay 2 days ago and light still on and normal height only still and today wife come home and it looked like car was doing nose dive front was down and back was fully up took out Fuses and got it to level out and on the display screen from left wheel has dropped down on screen and red flashing light
Any ideas
Cheers. Nick
|
| 28th Jul 2021 6:37 pm |
|
|
MikeO
Member Since: 15 Jan 2014
Location: The Cotswolds
Posts: 1391
|
Could be a height sensor but you really need a code reader to read fault codes and live values. 2016 Skoda Octavia VRS Estate
<gone>2009 FF Vogue TDV8 Buckingham Blue</gone>
<gone>2015 BMW 520D SE (not my favourite car)</gone>
<gone>2009 D3 HSE Galway Green</gone
|
| 28th Jul 2021 6:48 pm |
|
|
Spook1138
Member Since: 26 Jul 2021
Location: Loughborough
Posts: 14
|
| SUSPENSION RIDE HEIGHT/SPEED ISSUE… |
|
Hi all,
Very new here so please be gentle,
RRS 2006 2.7 - Front drivers side Ride Height Sensor replaced, successfully calibrated using IID tool, but if I go above 40 for longer than amount 30-45 seconds dash reads suspension fault, RED warning ‘suspension’ light, warning message 30MPH max speed and car lowers a to bumps!
If I park up switch engine off then on again fault goes away and car drives ok as long as under 40MPH.
Ironically, if I disconnect the new sensor everything appears to be ALL good other that after about 2 hours of driving the overall ride height becomes a little uneven, but this is resolved if I select off road height then normal height…..
I’d love to resolve this but I need a little pointing in the right direction…Ive purchased an IID fault reader so I’m all good to go…just need a LR knowledgable YODA like JEDI for educating this PADOWAN!…
|
| 13th Aug 2021 4:19 pm |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1822
|
You do know that there is a left and right side height sensors so check you have the correct one.
|
| 13th Aug 2021 11:21 pm |
|
|
Spook1138
Member Since: 26 Jul 2021
Location: Loughborough
Posts: 14
|
Yeah an aware of each ‘corner’ having its own independent height sensor, like I said the ‘offending’ one was replaced and now I have this issue relating to going faster than 40mph… 
|
| 14th Aug 2021 6:32 am |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
Have you looked at what its saying on the 4x4 screen it will show you if you have a sensor issue and which one is faulty.
Although you have replaced a sensor you may also have a wiring fault Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
| 14th Aug 2021 6:57 am |
|
|
